8086 Consultancy

Share a USB 3 device between two hosts or switch between two devices on one host. The bidirectional USB 3 Mux allows either a single USB device (or multiple devices when using a USB hub) to be...

USB3 Power Switch - Logic Level DefaultTurn your USB3 devices on/off using a switch or Pi/Pico/Arduino/etc. The USB3 Power Switch is available in two models, Logic Level (LL) and Open Drain (OD)...

Assembled - PicoIO64 with soldered 2x20 headers and socket for a Pico/Pico2 [W] with headers.The PicoIO64 adds 64 3.3V I/O pins (5V tolerant) to the Raspberry Pi Pico using four 16-bit XRA1403 SPI...

The USB Switch/Multiplexer allows a USB device (or multiple devices if connected via a USB hub) to be switched between two hosts, or powered off. This newer 4-pin version adds a 3.3V output which can...

The 8086 USB-USB NULL Modem (UUNM) is a back-to-back USB to Serial converter using USB CDC Serial - meaning drivers are already built in to most modern operating systems (Linux/Windows 10/Mac OS...

Power from each USB-C input (A/B) connector goes via a MOSFET "Ideal Diode" to the USB-C output connector. USB2 data from the USB-C port (A) is connected to the output USB-C connector (USB3 data is...

The Pico Dongle Lite is a small micro USB plug to Type-A plug adaptor designed for use with the Pico H/W from Raspberry Pi but will be useful for many other jobs. Whilst there are many similar...

PicoADC16 for Raspberry Pi Pico [W] The PicoADC16 is a 16-port 10-bit ADC (Analog-to-digital converter) supporting up to 3.3 volts with screw terminals for easier usage. The PicoADC16 is a 16-port...

8086 Consultancy - Fan controller for Raspberry Pi - Horizontal 2.54mm (0.1")Raspberry Pi/Fan not included this is just a controller. This is a small board with a load switch to allow a...

Handheld button/LED board designed for use with CircuitPython What is it? A multipurpose handheld device which could be used as a USB keyboard, keystroke replay, reacting to gestures, serial...

Connect Pi Zero and standard Raspberry Pi cables/cameras. The adaptor can be used to connect Pi Zero camera with integral (with 22-pin/0.5mm pitch) cable to full sized Raspberry Pi. Or with a 22...

Pi4, ClusterHAT, FanSHIM, etc. NOT included. Keep the 3.3v rail alive between reboots. When rebooting a Raspberry Pi 4 the 3.3 volt rail is reset which causes problems for some HATs. 3v3 Sustain fits...

Convert your Pi Zero to a Micro USB dongle (no soldering required) Connect your Raspberry Pi Zero or Pi Zero W[H] directly to peripherals with a Micro USB port such as the Official Raspberry Pi...

Power two devices from a single micro USB supply. Connects power from a single Micro USB connector to the Dual Female USB Type A connector. Micro USB data lines are connected to the lower USB port...

FOR USE WITH GIANT BUTTERFLY PCB Hardware Kit [ OPTIONAL ] The hardware kit includes everything  you need to mount the Giant Butterfly PCB on your Raspberry Pi and then mount up to four...

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB 2 OTG data over a separate USB-C connection (USB3 data is not...

Pi (3A+/etc), camera, camera cable, PSU are not included. What is it? APlusCam is designed in the shape of a Raspberry Pi HAT with mounting holes for a Raspberry Pi Camera and suction cups allowing...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB Type-A Female 4 - 6way long pin header Of...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB)...

The ClusterCTRL Stack (controller and passive backplane) is a simple way to both power and control cooling for a stack of 5 Raspberry Pi. Controller Powered by 12-24V PSU (not included). 20 pin...