The Adafruit Feather nRF52 Bluefruit is another easy-to-use all-in-one Bluetooth Low Energy board, with a native-Bluetooth chip, the nRF52832!  It's Adafruit's take on an 'all-in-one' Arduino-compatible + Bluetooth Low Energy with built in USB and...

If we could eat headers we'd have them for breakfast, lunch, and dinner.  But we can't : ( So we're making the best of it and selling them! This 2x20-pin strip, right-angle female header is a perfect companion piece to a 2x20-pin Dual Male...

Adafruit seesaw is a near-universal converter framework which allows you to add add and extend hardware support to any I2C-capable microcontroller or microcomputer. Instead of getting separate I2C GPIO expanders, ADCs, PWM drivers, etc, seesaw can be...

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to the popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for many...

Wow that's a tiny GPS antenna! This passive antenna is only 15mm x 15mm x 6.8mm in size, with a 50mm long uFL cable. Great for when you want to keep things small. Comes with a standard uFL connector on the end. Perfect for the FONA 808! Not good for...

"You see, wire telegraph is a kind of a very, very long cat.  You pull his tail in New York and his head is meowing in Los Angeles.  Do you understand this? And radio operates exactly the same way: you send signals here, they receive them there...

Adafruit has been looking for a display like this for a long time - it's only 1.5" diagonal but has a high density 220 ppi, 240x240 pixel display with full-angle viewing. It looks a lot like their 1.44" 128x128 display, but has 4x as many pixels and...

This flexible USB swivel adapter will extend your USB port out of the way. Useful when you want to attach a 'bulky' USB device without blocking a secondary port. We thought this would be handy for BeagleBone or Raspberry Pi users. Rotates 180 degrees in...

For use with classic 15-pin 1.0mm pitch flex cables, does not fit the Pi Zero's skinny CSI connector. Every time someone posts on the Adafruit forums and says they need to have a really long cable for their Pi Camera (CSI) or Pi Display (DSI), we...

"You see, wire telegraph is a kind of a very, very long cat.  You pull his tail in New York and his head is meowing in Los Angeles.  Do you understand this? And radio operates exactly the same way: you send signals here, they receive them there...

Hey Mr. DJ! Turn up that Raspberry Pi mix to the max with this cute 3W Stereo Amplifier Bonnet for Raspberry Pi. (It's not big enough to be an official HAT, so Adafruit called it a bonnet, you see?) It's the exact same size as a Raspberry...

Listen up! This set of two 2.8" x 1.2" speakers are the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. Adafruit likes these speakers as they are small and enclosed for good audio volume and quality. The pair...

This breakout board is the simplest way to create a project with a single "momentary" capacitive touch sensor. No microcontroller is required here - just power with 1.8 to 5.5VDC and touch the pad to activate the sensor. When a capacitive load is...

Three rows in a right angle header!? Yes! These chunks of 0.1" header has yet-another-row - handy for when you want to connect cables that come in sets of three, like perhaps sensors, or servos. These plug into any standard 0.1" spacing perf-boards or...

Round and round and round they go! 24 ultra bright smart LED NeoPixels are arranged in a circle with 2.6" (66mm) outer diameter. The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to...

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake off and no labeling. Then we thought about how people actually prototype - usually starting with...

This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this...

In collaboration with Google and Mongoose OS, Adafruit's releasing an IoT Core Pack based around their Feather HUZZAH32! This kit includes a pre-soldered Adafruit Feather HUZZAH with ESP32 WiFi and some sensors and components to get...

It's the Circuit Playground Express Base Kit! It provides the few things you'll need to get started with the new Circuit Playground Express. This version of Circuit Playground is super powered, and will work with Microsoft...

Now that we're carrying the Pi Zero, PaintYourDragon is back with another gorgeous laser-cut masterpiece. This time he's taken a pass at a Pi Protector for Raspberry Pi Zero, not quite a full case, it will keep your Pi Zero safe and svelte...