Transmission distance: >8m Effective angle: 60' Quiescent current: 3-5uA Dynamic current: 3-5mA Ideal for Arduino DIY project 17-key IR remote control Transmit 38KHz modulating signal PLEASE NOTE: The IR Receiver Module that comes with this remote...

The Explorer HAT Pro is a terrific prototyping side-kick for all Raspberry Pi boards with 40-pin GPIO's! (All boards except original B and B+ from 2014) On the Explorer Pro from Pimoroni there are a heap of useful input and output options that will take...

Connect this to that without soldering using these handy mini alligator clip test leads. 15" cables with alligator clip on each end, color coded. You get 12 pieces in 6 colors. Strong and grippy, these always come in handy! We often use these in...

The Raspberry Pi is a wonderful little computer, but one thing it isn't very good at is controlling DC Servo Motors - these motors need very specific and repetitive timing pulses to set the position. Instead of asking the Pi Linux kernel to send these...

Connect your own PCB to a Raspberry Pi and stack on top with this normal-height female header with extra long pins.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has extra...

Connect your own PCB to a Raspberry Pi with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs that do not to clear the USB/Ethernet jacks. This header has 3mm of pins, compared with Adafruit's...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed. They...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi Zero, A+, B+, Pi 2, Pi 3 and Pi 4 (any Pi with a 2x20 connector) with this jaunty prototyping HAT kit. To kick off the Adafruit HAT party, we have this Perma-Proto inspired...

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit with EEPROM To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid...

Weight : 9 g Size : 22 x 11.5 x 27 mm Operating Speed (4.8V no load): 0.12sec/60 degrees Stall Torque (4.8V): 17.5oz/in (1.2 kg/cm) Temperature Range: -30 to +60 Degree C Dead Band Width: 7usec Operating Voltage:3.0-7.2 Volts

This high-torque standard servo can rotate approximately 180 degrees (90 in each direction). You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with...

  One Terminal Strip, Tie-point 25. Material: ABS plastic Completely reusable. Accepts a variety of wire sizes (29-20 AWG). Red,green,blue,yellow ,white,and black are available for...

40 pin cable, 30cm in length. Cable type: female-female

The Raspberry Pi B+ / Pi 2 / Pi 3 / Pi 4 has landed on the Maker World like a 40-GPIO pinned, quad-USB ported, credit card sized bomb of DIY joy. And while you can use most of our great Model B accessories by hooking up our downgrade cable, its probably...

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2,Pi 3, Pi 4! Or just any Pi with 2x20 connector. The Raspberry Pi B+ and Pi 2 has landed on the Maker World like a 40-GPIO...

You got a Raspberry Pi Model B+ that you want to have work with some old kit or plate or breakout or something and it uses the classic 26-pinout. Very frustrating, it is...unless you have this ingenious 'downgrade' GPIO cable. It has a 40-pin socket...

Raspberry Pi 3 GPIO Extension Board For Raspberry Pi 2/3 Model Board Version 2.1 26 pin    

The Raspberry Pi YouTube Workshop kits is a selection of components that was chosen to accompany a series of step-by-step video tutorial posted on YouTube. It demonstrates how to use the Raspberry Pi's inputs and outputs, and how to program using Python...

RasClock is a highly accurate real-time clock that fits on a Raspberry Pi and includes a battery backup. Now available to purchase! RasClock uses one of the following chips: NXP PCF2127AT NXP PCF2127T NXP PCF2129AT NXP PCF2129T All of these have the...

The Fish Dish is a breakout/add on board for the Raspberry Pi (can be used with other boards too - Arduino etc.) which makes it easy and  extremely fun to use the GPIO on the Raspberry Pi. It plugs directly  onto the GPIO pins with a 2 x 13...